Like many a crafts person, I have several tool rolls, all of which I have made myself – for tools, paintbrushes, knitting needles – you name it, I have it in a tool roll! So I thought I would impart my knowledge and practice in the art of the tool roll so that one and all can have a go. You don’t need much fabric, but if you don’t have any – I have put together some kits which are available on my Etsy page, which are hopefully wonderfully tempting!
The lovely Helen from work has kindly tested these instructions for me and they have been adjusted as suggested!
You will need…
1 x patterned fabric – dimensions below
3 x plain fabric – dimensions below
1 x ribbon – 75cm long x 5mm wide (can be longer and wider if you’d prefer)
Sewing machine OR needle and thread (the latter will obviously take longer)
Dressmakers pencil (optional)
Finished Tool Roll:
– Firstly we are going to work on the tool side, so put the patterned fabric to one side.
– Iron a 2cm hem onto the long edge of both fabric 3 and 4, then put fabric 4 to one side for the moment.
– Line up fabric 3 with the bottom of fabric 2, ensuring both are front facing and the ironed hem is at the top of fabric 3.
– Pin these two pieces together
|TIPS – Pin the fabric with the pins perpendicular to the edge of the fabric, this will allow you to run your machine over the pins without misplacing them, it will also prevent the fabric from moving sideways against each other.
– The next step is to divide this new pocket up for the tools. I have made the partitions 2cm each, but you can make them whatever widths work well for your tools. Keep in mind that the divisions at the edges shrink when we sew the whole thing together, so it may be worth starting 3cm in and finishing about 3cm from the other end to allow for sewing round the edge.
– Pin fabrics 2 and 3 at the hem to stop it flapping about and then mark every point where you want to make a tool division – you could do this with pins, a dressmakers pencil, chalk or you could do it by eye.
– Starting from the base of the fabric, sew up in a straight line, perpendicular to the base of the fabric, to meet your first marker. You will need to remove the pin as you get there as the machine will not sew over it.
– Repeat this for each of your pin markers until you have made all of your tool partitions.
Your tool roll should now look a bit like this:
– We are now going to attach fabric 4 and form the lower pocket. This will be on the outside of the tool divisions we have just made.
– Firstly we must sew over the hem we ironed onto fabric 4 at the beginning – this is to stop it flapping about.
– Once hemmed, sew fabric 4 into place the same way we did for fabric 3. The new hem should be facing inwards.
– Next we are going to divide this pocket into two, as one large pocket will probably be less useful.
– Do this simply by sewing up the middle of of the fabric in line with one of the central tool partitions. If you have a variety of tool division widths – make sure you sew in line with one of them, otherwise you will sew up one of your tool divisions and it will be unusable.
– Nearly there! Next we are going to sew on our backing fabric – fabric 1 – and our ribbon tie all in one go.
– Fold your ribbon in half and pin it onto fabric 2 as shown in the picture – the long ends should be on top of your fabric and the little folded bit should be sticking out the edge.
– Sew along the edges of your fabric bundle, ensuring you leave an open space at the top to turn it inside out, about 12cm. The sewing edge can be up to 2.5cm due to the initial fabric pieces we cut, but try and keep the edges relatively small or your outer tool divisions won’t be much use.
– Turn it inside out and iron it nice and flat – at this point your ribbon should be nicely hanging on the right edge.
TIPS – Once you are definitely happy with the result, you can cut off the excess edges and corners on the inside of your tool roll, which should make it nice and neat on the outside – this is not essential to the finishing of the roll.
– FINALLY – sew up the open edge and fill with tools – TA DA!!
Don’t forget you can get ready prepared kits on my Etsy page to make these tool rolls, all made up from lovely fabrics from my stash and my local fabric shop – they are all very nice!
Once your all done – photograph your lovely tool roll and upload you picture to our maudie.made Facebook page and let me see all your hard work! Here’s Helen’s fabulous tool roll!
TIPS – If you found any of the tips useful, there is a tips jar in the sidebar!